S2K Commerce - Products Dropdown - South Central
Actions
S2K Commerce - Order Entry
Actions
Designed for Use with Aluminum, Copper, Brass and Welded Steel Tubing that Can be Flared
Recommended for Higher Pressures than those Covered by Compression Fittings
Resist Mechanical Pull Out
Made in USA
Made in USA
Not Intended for Steel Tubing
Designed for Use with Potable and Non-Potable Water, Instrumentation, Hydraulic and Pneumatic Systems
Little to No Tube Preparation Required. Connection Does Not Require Flaring, Soldering, or Other Types of Tube Preparation
Plastic and Pex Tubing Installations Require Sleeves and/or Inserts
Lead-Free
Designed for Use with Aluminum, Copper, Brass and Welded Steel Tubing that Can be Flared
Designed for Use with Fuel, Oil, Liquefied Petroleum (LP) and Natural Gas Lines
Resists Mechanical Pull Out
Recommended for Higher Pressures than Those Covered by Compression Fittings
Made in USA
Designed for Use with Aluminum, Copper, Brass and Welded Steel Tubing that Can be Flared
Designed for Use with Fuel, Oil, Liquefied Petroleum (LP) and Natural Gas Lines
Resists Mechanical Pull Out
Recommended for Higher Pressures than Those Covered by Compression Fittings
Made in USA
Not Intended for Steel Tubing
Designed for Use with Potable and Non-Potable Water, Instrumentation, Hydraulic and Pneumatic Systems
Little to No Tube Preparation Required. Connection Does Not Require Flaring, Soldering, or Other Types of Tube Preparation
Plastic and Pex Tubing Installations Require Sleeves and/or Inserts
Lead-Free
Bell Cast On
Bell Cast On
Bell Cast On
Throat of Drain is Threaded for Backwater Device
For Concrete Floors on or Below Grade
Dual Primer Bosses
Strainer is 1/2 Inch Thick
2 Inch Concealed Cleanout
Stands Upright for Easy Rough-In, also has Rough-In Tabs
Threaded for Backwater Device
Made in USA
18 Gauge Stainless Steel
Meets 900 Pound Downward Pull When Installed Properly
Meets Federal Specification WW-P-541/8B, Amendment 1, 16 April 1990
Meets ANSI 117.1 and all ADA Code Requirements
Meets Federal Specifications for FHA, VA Hospital, Private Construction
Individually Bagged with Stainless Steel Mounting Screws
Fits Over 3 Inch WV with a 4 Inch Sweep
with Plastic Swivel Ring
More Versatile than an Offset Closet Flange
Provides Unlimited Offset When Used in Conjunction with a Socket x Socket 45 Degree Elbow
Resistant to Corrosion and Damage Due to Freezing
Rated 100 PSI at 180 Deg F
NSF Listed Material
Designed for Use with Aluminum and Copper Tubing. Not Recommended for Steel Tubing
Little to No Tube Preparation Required. Connection Does Not Require Flaring, Soldering, or Other Types of Tube Preparation
Plastic and Pex Tubing Installations Require Sleeves and/or Inserts. Check Installation Instructions for Exact Requirements
Lead-Free
Made in USA
Ideal for Corrugated Metal Roofs
Ozone and UV Resistant
Pleated Cone Adjusts to any Pitch
Made in USA
Made in USA
Lead-Free
Green ABS Plastic Body and Ball
Buna-N Seals
Designed for Use with Aluminum and Copper Tubing. Not Recommended for Steel Tubing
Little to No Tube Preparation Required. Connection Does Not Require Flaring, Soldering, or Other Types of Tube Preparation
Plastic and Pex Tubing Installations Require Sleeves and/or Inserts. Check Installation Instructions for Exact Requirements
Lead-Free
Made in USA
Individually Wrapped Rods and Holders Boxed Together
Styrofoam Breaks Away or Melts with Flame
Eliminates Needless Chipping of Concrete
Styrofoam Breaks Away or Melts with Flame
Eliminates Needless Chipping of Concrete
For 1/4 Inch and 5/16 Inch Drives on Key
Fits 1/4 Inch Rod
Made of High Density Poly